Marvel Legends Maximum Series

Resilient said:
Today I boiled some water and let Deadpool (and Extremis 2.0) get a little hot water bath. I articulated their ab crunches that felt a little springy and hindered to the max the sculpt would allow and then let them cool while they were in that position. That seemed to fix the issue with the joint. If you do go to try this with Extremis 2.0, make sure you're careful of the paint on the Unibeam. It can scrape off VERY easily. I'd recommend clear coating it first.

Deadpool becomes a MUCH better figure once you get these joints working properly.
Click to expand...
What's your theory? Paint in the joint? Excess plastic?
 
Based on Extremis from when i took him apart, the bar that connects the lower and upper part of has four detents in it. You can feel it click the one time but it doesn’t click after that and he just springs back. I’m not super familiar with the inner workings on bodies with reverse abcrunch and torso rocker so it was new to me, but with Extremis Iron Man the bar slides into a soft rubber piece that also houses the torso rocker joint. Getting the heat/hot water to that part and rocking the joint forward seems to let that soft rubber piece form better to the bar somehow. I’m not 100% why it works but it works.
 
Resilient said:
Based on Extremis from when i took him apart, the bar that connects the lower and upper part of has four detents in it. You can feel it click the one time but it doesn’t click after that and he just springs back. I’m not super familiar with the inner workings on bodies with reverse abcrunch and torso rocker so it was new to me, but with Extremis Iron Man the bar slides into a soft rubber piece that also houses the torso rocker joint. Getting the heat/hot water to that part and rocking the joint forward seems to let that soft rubber piece form better to the bar somehow. I’m not 100% why it works but it works.
Click to expand...
It sounds like too few detents. Four? It's like when you don't have enough clearance on a hexagonal nut for an Allan wrench to get more than a quarter rotation. While I appreciate the new ab crunch, it's obviously not getting its full range without modification. I ain't cracking open a figure like what you described to fix something that should have been designed better. I appreciate you doing the footwork, your trial and error will benefit plenty. They really should have done the barbell/socket joints instead of that old ab hinge.
 
TheSameIdiot said:
I'm not sure about Hasbro itself, but consumer sentiment is definitely changing on the ab crunch. Seems like everyone is sick of it now.
Click to expand...
I don't mind it, but if they're going to do something new, like with Extremis, then do something that's most up to date.
 
Anyone who only wants Doop, I'd go halfsies with you. I need an extra of this DP for a custom, because of course, that's where I found the best parts lol. :rolleyes:
 
NORM said:
It sounds like too few detents. Four? It's like when you don't have enough clearance on a hexagonal nut for an Allan wrench to get more than a quarter rotation. While I appreciate the new ab crunch, it's obviously not getting its full range without modification. I ain't cracking open a figure like what you described to fix something that should have been designed better. I appreciate you doing the footwork, your trial and error will benefit plenty. They really should have done the barbell/socket joints instead of that old ab hinge.
Click to expand...
Just to be clear for everyone's sake: you can fix it without splitting the figure. I had just previously taken apart the figure to know how the inner workings work and that the there's only 4 detents on the bar. I don't know that DP is the same but i'm assuming so.
TheSameIdiot said:
I'm not sure about Hasbro itself, but consumer sentiment is definitely changing on the ab crunch. Seems like everyone is sick of it now.
Click to expand...
I don't hate the Diaphragm and Reverse Ab Crunch set up necessarily, but there's just a much better way forward, especially when you look at some of these Iron Man designs. Feels like Hasbro doesn't always consider the design of the armor when they're cutting in the articulation. (Yes, I'm talking about you, incorrectly labeled "Model 20" Iron Man with your bullshit waist cut when the design clear as day lends it self to ball joint in the waist).

I'll tell you I absolutely despise Ab Crunch and Waist Swivel now though. Shit is archaic.
 
You must log in or register to reply here.
Back
Top